Search This Blog

Monday, 15 June 2015

Vacuum forming machine

Between other jobs, over the last few weeks, I have been putting together a vacuum forming machine.


When looking at 3D printers I noticed that they cannot do proper transparent areas because they extrude in layers. The vacuum forming machine is to create windows.


I used one at college over 30 years ago, that one was made from a timber frame, some board and an industrial vacuum cleaner. I wanted something smaller so I knew it was fairly easy to make one from bits in my shed and the Internet confirmed that a normal home vacuum cleaner had enough power. All I needed was a box with holes in, some frames to hold the plastic and a heat source.


The design and photos show it all.  Instead of glue I used silicone sealant and screws to hold the joints of the box together. The better the seal the more the suction works where you want it.


By luck I had a 32mm cutter which is the exact size of the vacuum hose end.









In practice the vacuum pulls the hose end in to the hole to make a better seal so I did not need any gasket or other cover for the hose hole. There was plenty of suck to pull down the plastic. The grid of holes in the top of the box are all 4mm diameter in rows and columns 10mm apart and staggered.




I tried to use an old sandwich maker as the heat source but that didn't get hot enough so I resorted to the kitchen oven which I had already identified as suitable.  It was but I had to pay attention. Once the grill was hot it only took a minute for the plastic to droop and a few more seconds for it to run all over the oven shelf! I'll use a lower setting next time.

The grill in our oven only works when the door is closed so I had to remove the handles I had added to the frames to get the frame to fit. I had a very simple bent wire support from a disposable BBQ that was the ideal height to raise the frames, holding the plastic sheet, above the oven shelf.



By experimentation I established that the optimum time to take the plastic out of the oven was as the droop was about half an inch down. I must get round to cleaning the glass on the oven door to make it easier to see that stage.



My first experiments confirmed that the machine worked however my choice of mold was too ambitious. I could not get rid of the webbing on the tall section and the plastic, pulled in to the lowest thin slots, was too thin. That was disappointing but it confirmed in my mind that simpler, lower shapes would work.

Having the vacuum already on before putting the plastic on the mold worked best for me.




Sunday, 14 June 2015

Walls and more walls

I've been decorating the track in reverse order. Top down.


The overview of the track has looked odd to my eye up until now. At last there is something solid supporting the roads.





The walls are either made from floral foam, that I have mentioned before, or plaster filler on a hardboard backing.

The floral foam is easy to carve but has no strength. The plaster filler is too sticky and difficult to sculpt but is strong so can be used on very thin surfaces.




This time I used a bit more PVA glue on the foam. The first coat was a 50:50 mix but this time, once dry, I added a second coat of 75% PVA to 25% water. That plus the paint made the finished walls a bit stronger. Still easy to crush but it is less likely to be accidentally damaged.




While I was making the walls I also decorated some of the cut down barriers that I have been using. Little mounds of concrete and earth round the posts.





==

Edit: 16 June 2015

This is in reply to a question on the SlotForum asking to know more about how the walls were created.

There are three separate areas:
- The walls made from filler
- The walls made from floral foam
- Painting


==

Walls Made from Filler

In a couple of areas of the layout there was not enough depth to use floral foam. Thinking about what I had in my shed I decided to make them by spreading a thin layer of filler on to hardboard.

The filler was Ronseal Smooth Finish. It's very strong but has the disadvantage that it dries so hard it is virtually impossible to sand. I used a farrier's rasp to finish it off.

Technique:
- Cut the board to size
- Spread a thin layer of filler using a pallet knife
- Wait a few minutes for it to get less runny (not long because I have no patience.)
- Use a length of 9mm MDF as a ruler and spacer for the row height of the bricks
- Drag the pallet knife along the edge to form the horizontal mortar joints

The MDF would stick to the filler so this sometimes needed to be repaired after the line was drawn.

- Repeat for each row
- Hand draw the vertical joints with the pallet knife

This resulted in curled edges and corners, which bricks don't have. I had to go back over nearly every brick to sort out the corners!


I could not get a flat surface to the face of the bricks while the filler was wet. The pallet knife would pull the filler off the board! It had to be left for a day to go off.

As I said, the filler cannot be sanded once dry! I have a rasp given to me by a farrier. It was too blunt for his use on horses hooves but ideal for MDF and this filler.

- Rasp over the top of the filler to take off all the bits that stick up and give a level'ish surface.
- Further carve out some mortar joints with a knife where the rasping has removed the joint detail or where the curl was still too apparent.


Did someone mention the amount of work? :-)

That's it for the shape of the brickwork.
I then primed it ready for painting.

The decorative painting is the same for this and the floral foam walls, so I'll cover that at the end.

==

Floral Foam Walls

I have posted about using the floral foam before.

The foam is so easy to work with.
It is cut with a kitchen knife and the brickwork is simply drawn with a pencil.

This time, I glued the foam to a backing of MDF. This had two benefits. I could have long lengths and get the whole length the same depth, plus I could get the exact size to fit the terrain by cutting the MDF to fit tightly. Trying to do that with the foam always damaged the foam!

I used lots and lots and a bit more PVA wood glue on the back to attach it to the MDF. The foam soaks it up very easily but that gives the foam some strength.


The cat paw prints in the photo show how fragile the untreated foam is.

Do not get any PVA on the top surface of the foam yet. The PVA is nearly impossible to carve so ruins the result.

Cutting Tip:
- I used two equal height lengths of wood either side of the foam to get the same thickness over the whole length.
- Run the kitchen knife along the foam resting on the top of the lengths of wood

Brickwork Technique:
- I used layers of MDF as a ruler for the horizontal joints and drew with a normal pencil.
- I hand drew the vertical joints.

The arch was fun. I pushed a round plastic pot in to the foam to the depth I wanted then cut out the infill with the kitchen knife. I then drew the edge brick shapes round that arch, by hand.


So easy but you have to be very gentle to avoid crushing your own work!

- Clean out the joints with a small paint brush. Even the paint brush can carve the foam!
- Seal and strengthen with diluted PVA glue. Now you want the glue everywhere in every crevice.

PVA glue mixtures:
One layer of 50:50 PVA to water.
Let that dry for a day
Another thicker layer of 75:25 PVA to water.
It's now much safer to handle the walls and the PVA acts as a paint primer.


Let it all dry for a day then paint.

==

Painting

I don't claim anything special for the painting.  These are techniques I have learnt, mainly during my teenage years, by looking at others work and asking how they did it. Then a lot of trial and error.

In all cases my paint is water based. I don't get on with oil based paints!

Technique:
- Base coat of mat dark grey house paint.  Get in to all the mortar joints with a thin brush.
- Dry brush with a mat light grey house paint.

Dry Brushing:
Dry brushing takes practice but is exactly what it implies.
- For the brick faces I used a wide thin artists brush. Dip that in the paint to fill the bristles then wipe virtually all of it off on a cloth or I use a paper towel.
- The first stroke usually has too much paint, so go gently, hardly touching the work and drag it over the surface.
- As the paint is used you can drag a bit harder until eventually the brush is clean.

The aim is to get a non-uniform finish which is more natural.
I found only one layer of dry brushing was sufficient for this brickwork.

Dirt:
I now add the grub effect where the wall touches the ground:


- I'm using a small round artists brush
- Raw Umber (dark brown) artists acrylic paint
- A few bricks at a time
- Paint the lowest 5mm'ish of the mortar joints
- Dry brush the surface of the lowest part of the lowest bricks.
Don't be afraid to ruin the brush. The fluffier and fainter the effect the better.
I use a low cost brush but oddly, despite the mistreatment, it has survived and returned to normal afterwards for many uses.

Weathering:
This is the final treatment. The aim to is to add even more variation to the surface colour and get rid of that just painted clean look. It is not dramatic but that barely visible change is the finishing touch.

- Make sure the previous layers of paint are fully dry.
- Mix up some very watery black paint. Again I'm using mat house paint but any water based paint would do.
It's more like water with a bit of colour, it must not have any thickness.
- Soak a sponge in the dirty watery mix.
- Hold the wall at about a 45 degree angle over something that will not be ruined.
- Squeeze out the grubby water in random blobs and make sure it covers the whole thing. Dab in some places where the dribbles miss.
- Do it a couple of times and make sure plenty gets in the mortar joints.
It will probably be too subtle to notice and does not show the full effect until it is dry. You can see the difference if you compare an untreated section to a weathered length.
- Lay it flat, face up, to dry. The best effect is if some of the muddy water has pooled in some of the mortar joints.

Once dry the job is done.

Saturday, 13 June 2015

Ultimaker 2 Upgrade Parts

One of the fun things about the idea of 3D printing is that you can print improved parts for your own printer.

It's only day 2 and already I have created an addition for the printer. A clear front cover.


The prints can sometimes take several hours so the printer is going to be unattended for long lengths of time. With four cats there is always a chance of some inquisitive investigation. I'm not worried about the printer but when  it finishes printing the bed lowers to the bottom. It worries me that a cat could be under it when it does that!


The clear acrylic cover prevents access under the bed while the bed is raised during printing.

The top is still open but the cats are unlikely to get hurt by playing with the print head. It does get hot but they would feel that before it did any serious harm.



To support the cover I designed and printed a hook which is bolted to the acrylic sheet. The whole thing neatly hangs over the top edge.


The bolt holes are hexagonal with a step. The nuts are held in the holes so they cannot turn when the bolts are screwed in.


I printed it out using the quick setting. It has a few holes in it but it is still a completely serviceable component. This took about 1.5 hours to print compared to an estimated 5 hours on the normal setting.



I think it is now cat safe with the new cover.


Parts

Clear acrylic: 345mm deep x 310mm wide x 3mm thick.
Fixings: M4x15mm machine screws and lock nuts

Downloads

Blend file
STL file
Licence share alike

==


First 3D Object

I'll start by saying, much to my surprise it was a success first time out.


The measurements, I used in creating the 3D model, exactly matched the output so what I made fitted first time.


It was a cap, well two caps, to fit over the exposed nuts and bolts that hold the spot lights on the Discovery.


The printed parts needed a bit of cleaning up but just using a sharp knife to cut off fine bits of stretched plastic waste. I guess this is the additive version of swarf.




The Cura software used to prepare the model for printing gives an estimate of how long it will take to print and the length of filament that will be used.


The time is also displayed on the front of the printer when you select it to print. In fact the front panel of the printer is very easy to use.

Downloads

Blend file
STL file
Licence share alike

==


Calibrate the 3D printer

It arrived yesterday :-)


Very well packed in polystyrene and a webbing strap.

Un-boxing and following the initial instructions on-line or on the supplied card is fairly easy up until the point of feeding the filament.

The instructions did not tell me what to do if the feed mechanism started making a continuous clicking noise. I get a bit frustrated if the instructions I am following are not complete. I had to phone the place I got the printer.

The Creat3d support people were very helpful and patient several times during the afternoon.

Filament Feeding

The initial filament feeding problems were caused by the end of the filament not been straight.

TIP: The end of the filament on a new spool is likely to be bent to hold it on the spool.  Cut off any bent or damaged filament and make sure the end is square cut.

Anything that could get stuck on the sides of the Bowden tube will get stuck and cause the clicking sound and stalled progress that I experienced.

It still takes a little pressure to push the end in to the feeder at the back but if it is excessive the filament will probably also get stuck elsewhere!

TIP: Even with good clean filament I found that it was aided in the initial feed by holding the Bowden tube upright or in whatever position stopped the knocking sound.


During printing the knocking sound happens from time to time and I guess it is a necessary part of ensuring that the pressure of the feed is equal to that needed to extrude it from the hot head.

Bed Leveling

The next problem happened when I tried to print. I had followed the instructions for leveling the bed however I did not find their descriptions matched up to what I needed to do to get it to work.  Again, this was with more help on the phone.

The first problem was that the factory test print had left plastic stuck on the nozzle. As I had never seen one before I did not know this. After calibration of the bed, unknown to me, the head was way too far away because of the extra plastic thickness. My print did not stick to the bed!

Once hot I could see the extra plastic so had to abandon the print and clean the head. I used a handy box cutter to carefully lift away the excess plastic from the head.

I then calibrated the bed again!


For my next attempt, the filament extruded during the initial start-up of a print, that makes sure the extruder is working and dribbles plastic in the corner of the bed. All it did on the print was a fine goo that clogged round the head.

More phone calls and the person suggested that the head was probably too close to the bed, preventing the plastic coming out!

More bed leveling.  Luckily it is a quick task. This is the time where I have to deviate from the Ultimaker instructions, or at least my description of 'slight friction' is different to theirs.

MY WAY: Adjust the bed so the paper has slight friction and then loosen a tiny fraction so you can just feel the paper dragging on the head.


This variation could be because my paper is a different thickness to their paper!

We then proceeded to print a test earring that comes on the SD card with the printer. I selected this piece because it said it would only take 7 minutes. It took a fraction longer but still a quick thing as a test.


Easy To Use

Having had plenty of opportunity to play with the setting while setting it up I was impressed by how easy the menu was to use and to navigate. I have not needed to read anything to find the features I needed.


Once I get over the initial frustrations everything else has been simple.

So far I am very pleased with the Ultimaker 2.

Sunday, 7 June 2015

Close up spider

This year we have had at least one good sunny June day where I sat on the lawn with a cup of tea.

While there, a spider caught my eye walking under my legs.



I took a few photos with my mobile phone pointing where I thought the spider was and got some amazingly detailed shots.


You can clearly see the long hairs on the little creatures legs and the serrated edges of the grass.


He or she was less than 10mm long from eyes to the end of the abdomen.


Wednesday, 3 June 2015

3D Modelling using Blender

In preparation for getting a 3D printer I have started working on a 3D model of my own car.

I have worked on 3D models for my computer games and use the free open source programme Blender. I have lots of posts about using that on one of my other blogs.

I only use Blender every now and then, so I forget how to use it. To help speed up getting started each time I am creating a quick reference guide to remind me of the main features I use.



The guide will be a continuing work-in-progress.

Even though some of the posts using Blender will relate to 3D printing, I decided to keep all my general Blender posts in the same place, so anything about Blender will be added to my development blog.

Downloads

Download from the main article on my other blog